Acasă › Gaming
Controler incarcare baterii Litiu/Plumb 6-60V 30A

Controler incarcare baterii Litiu/Plumb 6-60V 30A

Cod: 1416414
Cel mai mic preț azi
48,40 lei
la robazar.ro
Mergi la robazar.ro

Prețuri în 1 magazin

MagazinPrețStocActualizat
robazar.roCel mai mic 48,40 lei În stoc 2026-11-19 Vezi oferta

Istoric preț minim

585348 2026-11-092026-11-19

Prețul minim pe zi, din toate magazinele urmărite. 11 zile de istoric.

Nota din toate magazinele

Nu am colectat încă note pentru acest produs. Le adăugăm pe măsură ce verificăm paginile magazinelor.

Descriere

Function description 1. Automatic Charge control function: By setting the volt-HI:‘UP’ volt-LI:‘dn’;When the battery voltage is below the volt-LI:’dn’,the relay leads,the charger begins to charge the battery;when the battery voltage is up to volt-HI:’UP’,the relay is diconnected and the automatic charge is completed once; 2. Charge Time Control Function: How to turn on the time control function?

After entering the parameter set, set the parameter op is non-zero, then turn on the time control function, op default parameter is:--:--h, the default does not turn on time control function;After the opening Time control function (OP is non-zero), when the battery voltage is the lower volt-LI’dn’, the charger began to charge the battery, the system began to clock; During the timing, the battery voltage ≥ volt-HI’UP’, relay disconnect; If the OP time is up, the battery voltage is still the lower volt-LI’dn’, the relay keeps the conduction, automatically closes the charge time control function, and flashes the H:ER to remind the user, the time parameter setting is unreasonable; Press any key to stop flashing;Note: Time format: 00:59 (00 for hours, 59 for minutes) The maximum time is 99:59, which is 100 hours. XY-L30A Lithium Lead-Acid Battery Charge charging Control Module 6-60V 30A Timer Overcharge Protection Relay board 3. Serial data upload and parameter setting function: The system supports UART data upload and parameter settingUART:115200,8,1 Data Upload message Format:Battery voltage + battery percent + charge time + charge status 12.0V,020%,00:10,OP XY-L30A Lithium Lead-Acid Battery Charge charging Control Module 6-60V 30A Timer Overcharge Protection Relay board 4.

Parameter Setting a) Press and hold the SET key to enter the setting interface;b) Switch the parameters you want to set by short press SET;c) After the selection of parameters, can be set by the UP/DOWN key to support the short press, long press (fast increase or decrease); To set other parameters, repeat step b, c);d) After all parameters are set, long press set key to exit and save; 5 Key Function Description: In the Run interface (main interface):Short press SET button to display the current set of parameters; Short press UP button, toggle display charge percentage and charging time;Short Press DOWN button, select Turn on/off relay enabling, if the relay can be closed, will show ' off ' as a reminder;Long press UP button, switch low power stateon:No operation in 10 minutes turn off backlightOFF:

Backlight is always bright

Long press SET button,enter the parameter settings. Calculation of voltage percentage:voltage percentage = battery voltage/(volt-HI – volt-LI)6. Additional Featuresa) Charging time recording function: not open charging time control, the product will record a full time, when the entry time display interface, flashing display charging time, and then exit time display interface or next charge to open (relay conduction) when empty;b) Automatic parameter detection: When the parameters are set, exit, if volt-LI dn≥ volt-HI UP, the system will flash display "ERR" as a reminder;c) Battery Access detection: This product attached to the battery, if not connected to the battery, the system will be shown in the downlink "NbE" as a reminder Controler incarcare baterii Litiu/Plumb 6-60V 30A

Descriere bazată pe informațiile furnizate de magazin.

Produse similare